How To Setup Wifi Router And Modem

Connection Between Ethernet Switch Router And Modem

Setting up wireless router with cable modem – configure router step by step

There are a handful of ways to set up a shareable home network connection, but the safest and most reliable way is to use a router and switch in combination. Once the switch is behind a router , all devices connected to either the switch or the router can access the internet simultaneously. Placing the router between modem and Ethernet switch creates an extra layer of protection from threats on the Internet.

Here are the detailed steps for connection:

Step 1: Unplug the power supplies of cable modem, switch and wireless router. Unplug any Ethernet cables that are plugged into any of them.

Step2: Connect telephone wire with modem, and then connect an Ethernet cable to the Ethernet port on the back of the cable modem.

Step3: Plug the other end of Ethernet cable connected with modem into WAN port of router.

Step4: Connect another Ethernet cable to numbered Ethernet port on the switch and plug the other end into the LAN port on the wireless router.

Step5: Plug the power supplies of the modem, Ethernet switch and router in. After two minutes, the network and Internet connection is ready to go.

How To Connect A Landline Phone To The Wifi Router

ByMorton Taylor published on February 14, 2022

Are you looking for a way to keep and use your old landline number? Do you know you can integrate it with your broadband internet service? You can bundle voice service with popular internet service providers like Spectrum, Verizon, and AT & T. It will not only bring down the cost but gets you a bunch of features as well.

Be it a home or a home office or a small business setup, having a voice phone will come in handy. The steps are more or less similar, irrespective of a router-modem combo or a separate modem setup. Find the steps involved in connecting your landline phone with the WiFi router for both cases.

Contents

Common Questions And Answers

Question- I want to setup VLANs but my iSP router doesnt support VLANs can I use a third party router?

Answer- Yes but you need to choose the correct type for your Internet connections see Beginners guide to home routers

Question I cant ping my home router from the Internet is it online?

Answer The router must respond to the ping and responses are disabled by default on most routers.

Question Does my Home router support NAT and what is NAT?

Answer NAT stands for network address translation and is a technique for sharing an IP address on IPv4 networks. All home routers support NAT.

Question -I disabled Wi-Fi on my router and now port forwarding doesnt work?

Answer My BT home hub seems to disable port forwarding if Wi-Fi is disabled. It could be a feature or just a fault.

You May Like: Factory Reset Blink Sync Module

How To Connect A Wireless Dsl Router To A Wireless Router

If your business already has a suitable Wi-Fi router in place, you may wonder what to do if you switch Internet providers and your new service comes bundled with a combination DSL modem and Wi-Fi router device. If you’re happy with your current router, or if your router is of higher quality than the bundled device your ISP has provided, you can continue using your router without worrying about the Wi-Fi router function of the DSL modem you’ve received.

  • 1.

    Configure your new DSL modem/Wi-Fi router device to disable its Wi-Fi hot spot feature. Check your specific device’s user manual for information on how to do this.

  • 2.

    Plug your existing Wi-Fi router into a power outlet.

  • 3.

    Connect one end of an Ethernet cable into the “WAN IN” port on your existing router, and connect the other end of the cable to an available “LAN” port on the new DSL/Wi-Fi router device. With the Wi-Fi feature disabled on your DSL modem, the device essentially becomes a modem only. By connecting your Wi-Fi router to a LAN port, you’re able to router the Internet connection from the DSL modem to your router, where users can then access the Web by connecting to your router’s hot spot.

  • 4.

    Connect to your router’s hot spot to test the Internet connection. If you experience any issues, refer to the DSL modem’s user manual for information on how to troubleshoot your connection.

  • Writer Bio

    Connect Gateway To Router

    How To Set Up Router And Modem

    First, turn off the gateway. If there is already an Ethernet cable plugged into the gateway’s local-area network port, unplug the cable and plug it into your router’s WAN port. Turn the gateway back on and wait a few minutes for it to boot up. Plug in the router’s power supply and turn it on, again waiting a few minutes.

    Read Also: Blink Camera Reset

    Configure A Second Router Without Subnetwork Support

    To set up a new router as a network switch, plug an Ethernet cable into any free port of the second router other than the uplink port. Then connect it to any port in the first router other than the uplink port.

    To set up a new wireless router as an access point, configure the device for either bridge or repeater mode linked to the first router. Consult the documentation for the second router for the specific settings to use.

    For both wired and wireless routers, update the IP configuration:

    • Check the second router’s local IP address and change it if necessary to ensure it is within the network’s address range as configured on the first router and doesn’t conflict with other devices on the local network.
    • Set the DHCP address range of the second router to fit inside the address range of the first router. Alternatively, disable DHCP and manually set the IP address of each device connected to the second router to fall within the first router’s range.

    How Do You Hook Up A Wireless Router

    Connect your router to your modem.

  • Connect the router and the modem with an Ethernet cable. Most routers come packaged with a short Ethernet cable that you can use for this.
  • Connect the modem to the WAN / Internet Port on your router. It is usually offset, and may be a different color from the LAN Ports.
  • Read Also: Free Wifi Dunkin Donuts

    How To Connect Ethernet Switch Router And Modem

    In the computer networking world, the three most ubiquitous pieces of equipment are Ethernet switch, router and modem. These are applied everywhere from data center to network connections in your own home. However, despite the importance of these three pieces of equipment, some people are oblivious or confused to their internal functions and connection mode. So in this article, we will attempt to explain the difference between each piece of equipment and introduce the common way to connect Ethernet switch, router and modem.

    What Level Of Wireless Security Should I Use

    Install a Cable Modem & Router

    When youre setting up your wireless network, youll be confronted with the choice of which wireless security you want to apply to your network. Its generally not a good idea to leave wireless security off because it means anyone can join your network, slurping up your bandwidth and potentially accessing files on connected systems depending on their sharing privileges.

    The lowest level of wireless security is called WEP and it only provides a very basic level of security. The one tiny advantage that WEP has is that some older wireless-capable devices only support WEP, but typically you should avoid it because its very easily broken into.

    WPA is a step up from WEP. It can be configured either as WPA-Personal with a pre-shared key, or WPA-Enterprise where a central server handles key configuration. For most home users, WPA-Personal is what you should opt for.

    WPA2 uses the AES for the highest current level of home user security over wireless. Ideally you should opt for WPA2 as long as your connected devices support it in order to enable the maximum level of security for your home Wi-Fi connection.

    You May Like: My Spectrum Self Install

    Where To Position Your Wi

    The most important step in setting up your wireless network is deciding where to place your wireless router. This will typically coincide with where your internet connection comes into your home or business premise, although in some cases it may make more sense to run additional connection cables to enable you to place your router more centrally within your dwelling.

    The reason for this is that most routers send out wireless signals omni-directionally, which means that

    The signal gets weaker the further away from the router you get.

    Unless you live in a remote location, its quite unusual to have the only wireless network in your area, which means youre all typically fighting for network clarity across what actually amounts to only a few different transmission bands. Unless theyre unsecured youre unlikely to end up on your neighbours Wi-Fi network, but the presence of their network can affect the reception you get from yours.

    Use The Second Router As A Switch Or Access Point

    The above procedures enable an additional router to support a subnetwork within a home network. This approach maintains extra control over specific devices, such as placing further restrictions on their internet access.

    Alternatively, a second router can be configured as an Ethernet network switch orif wirelessan access point. This arrangement lets devices connect to the second router as usual but does not create a subnetwork. A no-subnetwork setup is sufficient for households that want to extend basic internet access plus enable file-and-printer sharing to additional computers. However, it requires a different configuration procedure than given above.

    Don’t Miss: Change My Optimum Wifi Password

    Configure Your Wireless Router Gateway

    Most ISPs provide their customers with modemsaka gatewaysthat have routers built in. Unfortunately, these integrated modem/routers are usually of much poorer quality than stand-alone routers, and they are unlikely to allow you to build out mesh networks that have multiple wireless access points that enable you to blanket your home with Wi-Fi.

    If your gateway has an integrated router, youll need to configure the gateway to disable the router and pass the WAN IP address and all network traffic through to your new router. This is necessary to avoid double-NAT scenarios, among other things. Youll need to know the IP address that the gateway is using . Enter the IP address into a web browser to access the gateways configuration screen.

    PCWorld

    If your broadband gateway also has a built-in router, such as this Motorola NVG510, youll need to put the gateways router into bridge or passthrough mode to use your own router.

    Some gateways have whats known as a bridge mode for working with a secondary router others handle it differently. You might need to contact your ISP for help with this step, as some wont allow you to configure the gateway yourself.

    Michael Brown/PCWorld

    The Motorola NVG510 is a DSL modem that AT& T sometimes provides its U-Verse broadband customers. It has a broadband connector, a phone jack for internet phone service, and a four-port ethernet switch.

    Modem Vs Router Vs Gateway

    How to connect Linksys router to xfinity modem?

    As mentioned at the beginning, chances are youll run into a modem, a router, or a gateway in a home network. Folks tend to call these three arbitrarily or interchangeably, but they are distinctive hardware pieces.

    What is a modem?

    First of all, the modem is just one of many service-specific terminal devices. If you use DSL or Cable for your broadband, youd need a modem. But if you use Fiberoptic, then youd need an ONT.

    Considering that Cable Broadband has been widely used, you more likely run into a modem.

    That said, the word actually is MoDem. Its an acronym for a device that works both as a modulator and a demodulator. A modem converts computer data signals into those of the service line and vice versa.

    Its fairly easy to identify a modem. Its a device that always has one service port to connect to the service line, that comes into your home from the utility pole outside and one network port. This network port is where you connect to the routers WAN port, as mentioned above.

    Some cable modems also have a phone jack for phone service, and others might have an additional network port for WAN Link Aggregation, as mentioned above.

    But generally, when you see a service port on a device, it has a modem on the inside. Also, check the label you might find the word Modem on it.

    What is a router?

    Recommended Reading: Where Is The Reset Button On The Blink Sync Module

    How Do You Buy The Top 10 Best Modem Router Setup Our Top Pick’s

    Do you get stressed out thinking about shopping for a great modem router setup? Do doubts keep creeping into your mind? We understand, because weve already gone through the whole process of researching modem router setup, which is why we have assembled a comprehensive list of the greatest modem router setup available in the current market. Weve also come up with a list of questions that you probably have yourself.

    Huts Frankand Angies has done the best we can with our thoughts and recommendations, but its still crucial that you do thorough research on your own for modem router setup that you consider buying. Your questions might include the following:

    • Is it worth buying an modem router setup?
    • What benefits are there with buying an modem router setup?
    • What factors deserve consideration when shopping for an effective modem router setup?
    • Why is it crucial to invest in any modem router setup, much less the best one?
    • Which modem router setup are good in the current market?
    • Where can you find information like this about modem router setup?

    Were convinced that you likely have far more questions than just these regarding modem router setup, and the only real way to satisfy your need for knowledge is to get information from as many reputable online sources as you possibly can.

    This technology we use to assemble our list depends on a variety of factors, including but not limited to the following:

  • Features: What bells and whistles matter for an modem router setup?
  • Configure The Wireless Router Gateway

    In some cases, ISPs offer customers gateways with built-in routers. In most cases, these combined devices are not built for business environments, nor do they have extra ports, security, and other options that allow you to add services and expand networks as the business grows.

    If you have a gateway with an integrated router, you’ll have to configure the gateway to disable the router and pass the WAN IP addressthe unique Internet protocol address that the Internet provider assigns to your accountand all network trac through to your new router.

    If you dont take this step, you may run into conflicts that prevent devices from working properly. You may need to contact your ISP for help with this step.

    Read Also: How To Connect Blink Sync Module To Wifi

    Popular Articles

    Related Stories

    Stay on op - Ge the daily news in your inbox